i3000 Series IndicatorsInstruction ManualT32XW Indicator
EN-83000 Series Indicators1.3 Control FunctionsButtonPrimary Function (Short Press)ON/ZEROIf Indicator is On, sets zero.PRINTSends the current val
EN-93000 Series Indicators2. INSTALLATION2.1 UnpackingUnpack the following items: • Indicator • Mounting Bracket • Knobs (2) • Capacity
EN-103000 Series Indicators2.2.3 Battery PowerThe indicator can be operated on the internal rechargeable battery when AC power is not available. Th
EN-113000 Series IndicatorsRemove the four hex head screws from the rear housing.Open the housing by carefully pulling the top of the front housing fo
EN-123000 Series Indicators2.4 Mounting BracketAttach the bracket to a wall or table using fasteners (not supplied) that are appropriate for the t
EN-133000 Series Indicators3 SETTINGS3.1 Menu StructureTABLE 3-1. MENU STRUCTURE.CALIBRATIONSETUPREADOUTMODEUNITPRINTMENU LOCKEND S
EN-14 3000 Series Indicators3.2 Menu Navigation3.3 Calibration Menu Two calibration processes are available: Span Calibration and Linearity Ca
EN-153000 Series Indicators3.3.1 Span CalibrationSpan Calibration uses two points to adjust the scale. The first point is the zero value where ther
EN-16 3000 Series Indicators3.3.3 Geographical Adjustment Factor The Geographcial Adjustment Factor (GEO) is used to compensate for variations in gr
EN-173000 Series IndicatorsTABLE 3-2. GEOGRAPHICAL ADJUSTMENT VALUESElevation in meters0 325 650 975 1300 1625 1950 2275 2600 2925 3250325 650 975 130
ii
EN-18 3000 Series IndicatorsReset No, YesLegal for Trade Off, OnCal Unit kg, lbCapacity 5…20000G
EN-193000 Series IndicatorsTABLE 3-3. SETUP AND CALIBRATION VALUESCapacity Graduation size with LFT OFFGraduation size with LFT ON Span calibration po
EN-20 3000 Series Indicators3.4.7 Zero RangeSet the percentage of scale capacity that may be zeroed. 0% = zeroing disabled 2%
EN-213000 Series Indicators3.5.3 Auto-Zero TrackingSet the automatic zero tracking functionality. OFF = disabled. 0.5 d
EN-22 3000 Series Indicators3.6.2 Parts Counting ModeSet the status. OFF = Disabled ON = Enabled3.6.3 End ModeAdva
EN-233000 Series Indicators3.7.2 Kilogram Unit Set the status. OFF = Disabled ON = Enabled3.7.4 Gram Unit Set the statu
EN-243000 Series Indicators3.7.7 End UnitAdvance to the next menu. Reset No, YesBaud Rate: 300, 600, 1200, 2400, 4800,
EN-253000 Series Indicators3.8.5 HandshakeSet the flow control method. NONE = no handshaking. ON-OFF = XON/XOFF software han
EN-263000 Series Indicators3.9 Menu Lock MenuReset: No, YesLock Calibration Menu Off, OnLock Setup Menu Off, On Lock
EN-273000 Series Indicators3.9.8 End LockAdvance to the next menu. 3.9.7 Lock Print Set the status. OFF = Print menu is not locked.
EN-13000 Series IndicatorsTABLE OF CONTENTS1. INTRODUCTION ...
EN-283000 Series Indicators4.6 Application ModesOnly modes enabled in the mode menu will be displayed (refer to Section 3-6).4.6.1 WeighingPlace
EN-293000 Series IndicatorsRecalling a Stored APWPress the No button to recall the existing APW.Press the FUNCTION Mode button to temporarily display
EN-30 3000 Series Indicators5 SERIAL COMMUNICATION The Indicator include an RS232 serial communication interface. The setup of RS232 operating
EN-313000 Series Indicators5.2 Output FormatDefinitions: Polarity, “-” sign if negative, blank if positive. Weight, up to 6 numbers a
EN-32 3000 Series Indicators6. LEGAL FOR TRADEWhen the indicator is used in trade or a legally controlled application it must be set up, verified
EN-333000 Series Indicators Figure 6-1. Wire Seal Figure 6-2. Paper Seal SEALSe
EN-34 3000 Series IndicatorsThe audit trail information is displayed in the format CFGxxx and CALxxx.Then the indicator returns to normal operation.CA
EN-353000 Series Indicators7 MAINTENANCE CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE CLEANING.7.1 Indicator Clea
EN-36 3000 Series Indicators TABLE 7-1. TROUBLESHOOTING (Cont.).SYMPTOM PROBABLE CAUSE(s) REMEDYError 8.1 Wei
EN-373000 Series Indicators8. TECHNICAL DATA8.1 SpecificationsMaterials Housing: stainless steel Keypad: polyester Display Window:
EN-23000 Series IndicatorsTABLE OF CONTENTS (Cont.)3.5 Readout Menu ...
EN-38 3000 Series Indicators8.2 AccessoriesTABLE 8-2. ACCESSORIES. DESCRIPTION PART NUMBERColumn Mount Kit, 35 cm painted steel 80251743Column Mo
EN-393000 Series Indicators8.3 Drawings and DimensionsFigure 8-1. Indicator Overall Dimensions with Mounting Bracket.239 mm212 mm9 in.8.3 in.149mm
EN-40 3000 Series Indicators8.4 ComplianceComplianceCompliance to the following standards is indicated by the corresponding mark on the product.Ma
EN-413000 Series IndicatorsDisposalIn conformance with the European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE) this devi
LIMITED WARRANTYOhaus products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warran
Ohaus Corporation 19A Chapin RoadP.O. Box 2033 Pine Brook, NJ 07058, USATel: (973) 377-9000 Fax: (973) 593-0359www.ohaus.comP/N 80252869 © 2009
EN-33000 Series IndicatorsTABLE OF CONTENTS (Cont.)3.10 Security Switch ...
EN-43000 Series Indicators1. INTRODUCTIONThis manual contains installation, operation and maintenance instructions for the T32XW Indicator. Please r
EN-53000 Series IndicatorsItem Description1 Data Label2 Front Housing3 Adjusting Knob (2) 4 Control Panel5 Mounting Bracket6 Screw (4)7 Rear Housing8
EN-63000 Series Indicators1.2 Overview of Parts and Controls (Cont.)Item Description1 Keypad Connector J82 Battery Connector3 Line Power Input4 Se
EN-73000 Series Indicators1.2 Overview of Parts and Controls (Cont.)No. Designation1 Capacity Label Window2 Pound symbol3 Ounce symbol4 Kilogram,
Comments to this Manuals